久久精品国产亚洲欧美成人,国产自国产在线无毒不卡,四虎影视永久在线精品,亚洲中文字幕久爱亚洲伊人

歡迎光臨
手機網站 | 聯系我們：021-32535039 | 加入收藏
  • 技術文章

    Ford CETP-00.00-L467實驗室加速循環腐蝕試驗

    2021-03-30 08:34:45  來源：上海鼎徵儀器儀表設備有限公司

    1.0 introduction 介紹
    1.1 TEST SCOPE 試驗范圍 上海鼎徵儀器儀表設備有限公司
    This standard specifies an accelerated laboratory atmospheric corrosion test. The testing environment addressed is similar in effect to that of the salt load/ climatic part of the proving ground corrosion test procedure, CETP 00.00-R-343 and yields corresponding results. The objective of the test is to allow evaluation of the corrosion resistance of metals in environments where there is a significant influence of chloride ions, mainly as sodium chloride from a marine source or by winter road de-icing salt. The laboratory test provides full exposure to the salt load and humidity environment. It does not attempt to simulate other engraving factors such as mud loads, temperature stresses or wear.  It serves as a general purpose atmospheric corrosion test and applies to a variety of materials, coatings, and interactions of materials, both as test specimens or in designed components. The test can be used as a design verification method in order to (a) develop and qualify new corrosion resistant products, (b) develop new pre-treatments and finishing processes, (c) select materials and, (d) perform quality control of the final product.
    本標準是關于一項在實驗室里加速進行的大氣腐蝕試驗。本文所述的試驗環境類似于《試驗場腐蝕試驗程序CETP00.00-R-343》中的鹽負荷/環境影響部分，得出相應的結果。試驗?zāi)康脑谟谠u(píng)估金屬在富含氯化物的環境中（主要是海水中的鹽或冬天用于融雪的鹽）的抗腐蝕性。該實驗室試驗主要是將試驗件完全暴露在濕潤的鹽負荷環境中，而非模擬其他摩擦因素如泥負荷、溫度壓力或磨損。該試驗主要作為一項大氣腐蝕試驗，適用于各種各樣的材料、涂層、試樣或設計零部件材料的相互作用。該試驗可作為一種驗證設計的方法，用于(a)開發并驗證新的抗腐蝕產品；(b)開發新的預處理和表面處理工藝；(c)選擇材料；(d)對*終產品的質量控制。
     
    The standard specifies controlled conditions for equipment and procedures to allow the test to be performed with a high degree of repeatability and reproducibility. It is designed to be suitable to run in various climate chambers, either as a fully automated procedure or with partial manual operations.
    本標準說明了設備和程序的受控條件，讓實驗具有高度的重復性和再現性。本標準適用于多種環境試驗箱，包括全自動試驗或部分手動操作的試驗。
     
    1.2 SUMMARY OF TEST CONTENT 試驗內容摘要
    The workday test procedure consists of: 工作日的試驗程序由以下幾個方面組成：
    A 6 h wet phase at room temperature. with intermittent exposure to salt solution (0.5% NaCl).
    A 2.5 h transition phase with drying under climate control.
    A 15.5 h phase with constant temperature and humidity (50°C, 70% RH).
    室溫下6小時的加濕階段，間歇曝露到0.5%的氯化鈉溶液中
    2.5小時的過渡階段，通過環境控制進行烘干
    15.5小時的恒溫恒濕階段(50°C, 70% RH)
     
    After repeating this procedure Mon-Fri a 48 h weekend phase under continued constant climate control is added.
    從周一到周五重復該試驗程序后，在周末加入持續恒定環境控，進行48小時的試驗。
     
    1.3 COMMONALITY 共通性 上海鼎徵儀器儀表設備有限公司
    This is a CONTROL TEST and can be used to qualify components throughout the world.  The test may be conducted at any location having the necessary equipment and facilities.  Proposed revisions to this procedure must be submitted per FAP03-179. 
    這是一項可驗證世界上所有的零部件的控制試驗，可在任何地方進行，只要具備所需的設備儀器。對本試驗程序的修改建議必須按FAP03-179提交。
    2.0 Instrumentation 儀器 上海鼎徵儀器儀表設備有限公司
    The following elements are usually required to conduct the test procedure:
    進行試驗程序一般需要以下儀器：
     
    2.1 Compressed, clean air of 4 - 6 bars for cleaning salt solution from spray nozzles, as a source for the renewal of chamber air and for humidification, supplied by spray humidifiers.
    2.1    4-6 bar的干凈的壓縮空氣，用于清理噴嘴上的鹽溶液、箱內換氣和噴霧加濕器進行加濕。
     
    2.2 A low conductivity water supply (20 mS max) for humidification or evaporative spray humidifiers and for the preparation of salt solutions.
    2.2    一根低導電率的供水管（至大20 mS），用于加濕或噴霧加濕器以及準備鹽溶液。
     
    2.3 A tank for preparation and storage of salt solution or, alternatively, a system for direct on-line mixing of water and saturated NaCl solution to the actual concentration (0.5 ± 0.05% by weight)
    2.3    一個用于準備和存儲鹽溶液的水槽，或者一套直接在線按實際濃度（0.5 ± 0.05%，按重量）混合水和飽和氯化鈉溶液的系統。
     
    2.4 A conductivity meter with built-in temperature compensation for preparation and control of the 0.5% NaCl salt solution (conductivity: 8.3 mS/cm + 0.80 at 20°C). A 0.50% by weight NaCl solution is used as a calibration standard at each measurement.
    2.4    一個帶內置溫度補償?shù)碾妼?dǎo)儀，用于準備和控制0.5%的氯化鈉鹽溶液（溫度為20°C時的導電性：8.3 mS/cm + 0.80）。 一份按重量為0.50%的氯化鈉溶液，作為每次測量時的校正標準。
     
    2.5 A high quality device for independent control of temperature and relative humidity shall be accessible. This instrument shall on a stipulated regular interval (Ref 5.4) be used for independent monitoring and calibration of the conditions in the very test plane of the exposure chamber. The total measurement error must not exceed 0.1°C.
    2.5    一套高質量的設備，用于獨立控制溫度和相對濕度。該設備按照規定的時間間隔（參考5.4），獨立監控和校正試驗箱李的試驗平面上的各項條件，測量總誤差不超過0.1°C。
     
    2.6 Racks of inert material for support and aligned fixation of test specimens must not hamper a free air-flow around the test objects, nor collect standing wetness. The test objects in a rack must not screen one another from the salt solution downfall and they should be exposed with the stipulated exposure angle to the spray (15- 20 degrees inclination from vertical).
    2.6    由惰性材料制成的夾具，用于支撐、排列和固定試樣，但不得妨礙試樣周圍的空氣流通，不得累積水分。夾具上的試樣不得相互遮蔽導致鹽溶液淋不到試樣上。試樣應按規定的角度曝露到噴霧中（偏離垂直線15-20度）。
     
    2.7 Pressurized hand-spray equipment for application of the 0.5% NaCl solution if a manual spray procedure is used. The capacity must be sufficient to meet the downfall requirement (Ref. 3.3.1).
    2.7    如需采取手動噴灑，應使用適用于0.5%鹽溶液的加壓型手動噴霧器，噴霧器的容量必須能滿足噴灑要求（見3.3.1）。
     
    2.8 Funnels, beakers/ measuring glasses and a balance with at least 0.1 g accuracy for monitoring and calibration of salt solution downfall throughout the test plane of the exposure chamber.
    2.8    漏斗、燒杯/量杯以及精度至少為0.1g的天平，用于監控和校準曝露箱中試驗平面上落下的鹽溶液。
     
    2.9 All test measurement equipment must be calibrated and maintained per FAP03-015, Control, Calibration, and Maintenance of Measurement and Test Equipment.
    2.9    所有試驗的測量設備的校準和維護必須按照《FAP03-015測量和試驗設備的控制，校準和維護程序》。
     
    2.10 All applicable safety guidelines and procedures must be followed.
    2.10  試驗須遵守所有適用的安全指引和安全程序。
     
    3.0 Equipment and facilities 設備設施 上海鼎徵儀器儀表設備有限公司
    The necessary, permanently installed facility to conduct the test consists of a programmable humidity chamber of good quality. It is preferably equipped with an integrated rig for spraying salt solution of the required amount and accuracy, cooling capacity and a good internal circulation system for the conditioned air (Fig. 1). The exposure chamber shall be designed so that the test conditions described in the subsequent paragraphs can be obtained, controlled, and monitored during the test.
    試驗所需安裝的設施包括一個可編程的高質量濕度箱。濕度箱中建議能配備一套噴量準確度高的綜合性鹽霧噴灑裝置、冷卻裝置和一套性能良好的空氣內循環系統（如圖1）。曝露箱應按要求設計，以使下文所述的試驗過程中的各項條件能在得到滿足、控制和監控。
     
    Fig. 1 Schematic view of a climate chamber equipped with functions suited for performance of the described test procedure: 1. Chamber test space, 2. Climatization unit, including fan, heating, cooling and humidification, 3. Test plane with samples, 4. Temperature/ humidity sensor for regulation, 5. Insulated walls/ lids, 6. Diffusors for improved air distribution, 7. Fresh air inlet/ "bleed", 8. Rain rig with nozzles and motor for swaying mode, 9. Gutter, 10. Control/ steering/ recording unit, 11. Position for monitoring/ calibration of climate with independent temperature/ humidity sensor.
    圖1 環境試驗箱的圖示，配備了進行本文所述的試驗程序所需的功能：1. 試驗空間；2. 環境系統，包括風扇、加熱器、冷卻器和加濕器；3. 放置試樣的平面；4. 溫濕傳感器（調節用）；5. 隔熱壁/蓋； 6. 空氣擴散器（改善空氣分布）；7. 新鮮空氣進氣口； 8. 帶噴頭和搖擺模式驅動馬達的噴灑器；9. 排水口；10. 控制/操作/記錄系統；11. 帶獨立溫室感應器的環境監控/校正位置。
     
    3.1 CLIMATE CONTROL 環境控制 上海鼎徵儀器儀表設備有限公司
    The humidity and temperature levels of the chamber during the test cycle shall be continuously monitored.  The sensors should reflect the climate conditions in the test "plane" (Fig. 1, item 4). The mean value of the constant temperature/ relative humidity climate conditions must be within ±0.4°C and ±2% relative humidity (RH) respectively vs. the real, set value, i.e. these are the max tolerable mean offsets caused by the sum of calibration errors.  At annual calibration this degree of accuracy must be fulfilled for the following three constant conditions: 25°C, 95% RH, 50°C, 95% RH and 50°C, 70% RH. At bimonthly control, during normal operation, this accuracy should be fulfilled at the constant climate conditions (50°C, 70% RH) during a work-day cycle.
    試驗過程中應連續不斷地監控試驗箱的濕度和溫度水平。傳感器會反映試驗“平面”上的環境（如圖1中第4項）。恒定溫度/相對濕度的均值必須在±0.4°C范圍內，相對濕度（RH）在±2%，分別對應實際值、設定值，這些就是由于累積的校正誤差造成的平均偏移值的至大允許范圍。 在年度校正過程中，這一精度必須得到滿足，以保證以下三項恒定條件：25°C, 95% RH, 50°C, 95% RH以及50°C, 70% RH。在進行兩月一次的正常控制時，工作日循環中的恒定環境條件（50°C, 70% RH）應能到達這一精度。
     
    The maximum allowed short-term fluctuations in relative humidity overlaid on the calibrated mean value is ±3% RH, which implies a maximum allowed short-term temperature fluctuation of ± 0.6°C.  Figure 2 is exemplifying the requirement on relative humidity.
          疊加到校正平均值的相對濕度短期波動至大范圍是±3% RH。這意味著短期溫度波動的至大范圍只能是± 0.6°C。圖2舉例說明了相對濕度的要求。
     
     
    Fig. 2 Accuracy requirement on humidity deviations from set value
    圖2  濕度偏差離設定值的精度要求
     
    The chamber controlling software/ hardware must be designed so that the relative humidity may be changed linearly with time as depicted in the illustrated test conditions, see Figure 5. In the 2-stage ramping from a wet chamber at 25 ±2°C to humid conditions at 50°C, 70% RH, the first heating stage to 40°C should be reached within 30 minutes without sample drying, which is secured by a nominal relative humidity setting to 95% RH. The second 2 h ramp must reach the stipulated final 50°C, 70% RH at the end of the ramp.
    控制試驗箱的軟件/硬件必須設計成能使相對濕度隨時間呈線性變化，如圖5所示。從試驗箱溫度為25 ±2°C的濕潤狀態到50°C, 70% RH的濕潤狀態需經過兩個階段。一階段應通過將相對濕度讀數設定到95%RH，以保證溫度在30分鐘內達到40°C而試樣不干燥。第二階段為兩小時，必須在結束前達到規定的50°C, 70% RH。
     
    NOTE: For each new exposure situation this condition must be verified by an independent monitoring device (paragraph 2.5) with the sensor positioned among the actual test objects in their actual average plane of exposure (Fig. 1 Item 11). For monitoring : Deploy the sensor directly after the last spray event of the work-day wet phase.
    注意：每次曝露的條件必須經過獨立監控設備驗證（見第2.5段），也就是實際試驗物體所在的曝露平面之間的傳感器（如圖1，第11項）。在工作日濕潤階段的*后一次噴灑后直接調節傳感器來進行監控。
     
    In automated testing, forced cooling is necessary when proceeding from 50°C, 70 % RH controlled, constant conditions to macro-wet conditions at 25°C.  The chamber must achieve a cooling from 50°C to 30°C within 30 minutes with the targeted 25°C met within 1 hour. If spraying is applied manually, then cooling the samples by letting the chamber be open with test objects kept wet may provide an option that does not require the use of a built-in cooling unit. It must be verified by temperature monitoring that cooling requirements are fulfilled under such conditions for the actual chamber type and test specimen load. 
    在自動試驗過程中，要使試驗箱從受控恒定條件50°C, 70 % RH變化到25°C下非常濕的條件，需要進行強制冷卻。試驗箱必須在30分鐘內從50°C冷卻到30°C，然后在1小時內到達目標溫度25°C。如果是手動噴灑，可以打開試驗箱同時讓試樣保持濕潤，這樣就不必使用內置冷卻系統。在這種條件下要滿足該類試驗箱和試樣負荷的冷卻要求，必須通過溫度監控保證。
     
     
    3.2 RECOMMENDATIONS ON TEST CHAMBER FUNCTIONALITY 
    關于試驗箱功能的建議 上海鼎徵儀器儀表設備有限公司
    In order to meet the temperature and humidity accuracy requirements throughout the test area, the chamber should be equipped with means to provide well distributed circulation of conditioned air (meaning a local air velocity of at least a few cm/s over all parts of the test area, - Fig. 1 is exemplifying such a condition). Sufficient insulation of the chamber walls and lids is required in order to avoid excessive condensation on these surfaces.  The more efficient air circulation, the less insulation is required.
    • 為了在整個試驗過程中滿足溫度和濕度的精確度要求，試驗箱應配備能使經調節溫濕度、空氣流動性好的裝置（試驗區域內各部分的內部氣流速度至少是若干厘米/秒-例如圖1。）試驗箱的四壁和蓋板要求得到有效隔熱，以避免這些表面出現過渡冷凝。空氣流動性越好，隔熱需求越少。 
      Wall heating should be avoided, due to that heating by radiation tends to keep test object close to the chamber walls locally too dry to be within humidity specification (or a screen shall be installed to avoid such an effect). Provided the internal air circulation is efficient, wall heating is not required.  The chamber air must be continuously renewed by a purge of not less than
      1 m3/ h per m2 of test area (exemplified by Fig. 1, Item 7).  This to assure that the CO2-level is not significantly depleted under any exposure conditions.  Fresh air can be added dry from a compressed source or taken from ambient conditions, unless significantly polluted (> 50 ppb SO2).
      由于熱量輻射會使靠近箱壁的試樣過度干燥，達不到濕度要求，因此應盡量避免試驗箱壁受熱（或者添加遮擋板來避免受熱）。如果內部空氣流動良好，就不必進行箱壁加熱。應配備1 m3/ h每m2的空氣凈化器使試驗區域內的空氣不斷更新（例如圖1第7項）。這是為了保持CO2水平，避免其在曝露條件下被耗盡。干燥的新鮮空氣可以由壓縮機提供，或使用室內的空氣（除非空氣被嚴重污染（> 50 ppb SO2））。
       
       
    3.3 EXPOSURE TO SALT SOLUTION 曝露到鹽溶液中
    3.3.1 For a fully automated procedure , the chamber shall be equipped with a spray device capable of producing a finely distributed, uniform spray falling on the test objects. The most reliable way of receiving a fairly uniform downfall is by installing a moving spray device, like the swaying rail with overlapping nozzles, depicted in Fig. 3. The spraying device shall be made of corrosion resistance materials.  Plastic is recommended.
    3.3.1  對于全自動的試驗，試驗箱內應配備噴灑裝置，能使溶液得到妥善分配，均勻噴灑到試樣上。*能有效使溶液均勻噴灑的方法是安裝一套可移動的噴灑裝置，如帶交叉噴頭的搖擺軌道，如圖3所示。噴灑裝置應由耐腐蝕材料制成，建議是塑料。
     
     
    Fig. 3 Example of spray rig for obtaining uniform salt solution downfall.
    圖3 使鹽溶液均勻噴灑的噴灑裝置示例
     
    A target average precipitation rate distributed over the workday 6 h wet period of this test procedure period is 5 L/m2, and shall not exceed 10 L/m2.  For any local position the total precipitation over the 6 h period must not be lower than 3 L/m2 and not exceed 15 L/m2. Suggested nozzles type: Spraying Systems Uni Jet 800050VP.  Mount the nozzles on a supporting tube 50-60 cm apart and about 1 m above the test objects.  The nozzles shall be adjusted so that the fan plumes are in line with the tube/ supporting rail. An individual filter at each nozzle is strongly recommended to avoid any contaminations in the tiny slots. These low-cost plastic nozzles have a reliable function, but must be inspected in microscope at delivery in order to discard such with defect slot cuts. Stainless nozzles, even in 316 alloy, will be impaired by corrosion under the actual test conditions. Atomizing salt-spray nozzles should not be used, since they generate a too low precipitation rate to give sufficient leaching effect on the test objects. Achieving a uniform downfall with these types of nozzles can be difficult.
    在本試驗的工作日的6小時加濕階段，平均噴灑密度的目標值為5 L/m2，且不能超過10 L/m2。在6小時周期內，箱內任何位置的噴灑密度都必須不低于3 L/m2，不高于15 L/m2。建議噴頭類型：Uni Jet 800050VP噴灑裝置。將噴頭裝在支承管上，相隔56-60cm，處于試樣上方1米左右。調整噴頭，使扇葉與支承管/支承軌成一直線。強烈建議在給每個噴頭裝上過濾器，以避免小槽中的污染物。雖然這些噴頭價格低廉、功能可靠，但是發貨時還須經過顯微鏡檢驗，以淘汰那些小槽切割不良的噴頭。不銹鋼噴頭，就算是用316合金制成的，在也會在實際試驗條件下受到腐蝕而損壞。霧化鹽霧噴頭噴灑密度過低，無法為試樣起到有效的過濾作用，故不宜使用。這幾類噴頭噴灑都不均勻。
     
    3.3.2 An automated spray-rig is allowed to be separated from the humidity chamber, i.e. the test objects are moved between two units on a work-day basis.
    3.3.2 自動噴灑裝置可從加濕箱中拆出來。也就是說，試樣在一個工作日內在兩套設備之間移動。
     
    3.3.3 If there is no possibility to use an automated device for spraying, a manual spraying of the test object is allowed, either in or outside the test cabinet, provided: 1. The minimum precipitation rate of 5 L/m2 per 6 h wet session is fulfilled, 2. The spraying events are distributed over the 6 h period, so that the test object are kept constantly wet, and 3. The temperature requirement is fulfilled.
    3.3.3 如果不能采用自動噴灑裝置，可采用手動噴灑，在箱內箱外皆可，條件是：1. 在6小時加濕階段完成前，噴灑密度至少為5 L/m2。2. 噴灑將分布在6小時周期內，以使試樣保持濕潤；并且；3. 保持要求的溫度。
     
    NOTE:  Salt solution sprayed onto test objects must not be reused.
    注意：噴灑到試樣上的鹽溶液不得重復使用。
     
     
    4.0 Sample preparation 試樣準備
    Sample preparation before exposure, the sample orientation during exposure and the evaluation after exposure are usually stipulated in the engineering test standards addressing this test procedure.
    曝露前試樣準備，曝露期間的朝向和曝露后的評估方法一般會在本試驗程序相關的工程試驗標準中關于有所規定。
     
    4.1 Painted and scribed panels:  The test is optimized for exposing scribes in horizontal position on panels oriented to the angle stipulated in Paragraph 5.1.1.  Scribe orientation has a similar effect on salt collection as the panel orientation.  The scribe, or other type of damage, shall be positioned, so that a collecting area for precipitation is left above the exposed area of interest.
    4.1   噴漆板和劃線板：本試驗已針對水平劃線的板材按第5.1.1段所規定的角度朝向曝露進行了優化。劃線的朝向的作用類似于板材朝向的鹽聚集。劃線或其他損傷都應定好位置，以便噴灑液收集區域位于目標曝露區域之上。
     
    4.2 Component parts are to be in vehicle orientation position if at all possible.  The salt solution spray should reach the areas of interest.
    4.2    如果可能，零部件應盡量按照汽車朝向放置，并使鹽溶液能淋到達目標區域。
     
    4.3 Interested parties should agree on the location within the components where the corrosion is to be observed.
    4.3    相關各方需商定零部件上將出現腐蝕的位置。
     
    4.4 Interested parties should agree to any pre-conditioning, masking of edges, pre-testing, cleaning, or any other sample preparations.
    4.4    相關各方需商定預處理、要遮蓋的邊緣、預測試、清潔或其他試樣準備工作。
     
    4.5 Interested parties should agree to any photographic details throughout the test and the areas to be examined and any assessments that are required.
    4.5    相關各方需商定試驗過程的具體細節、檢測的區域以及要求的評估。
     
     
    5.0 OPERATION 操作 上海鼎徵儀器儀表設備有限公司
    5.1 BEFORE TEST START   試驗開始之前
    Prepare test objects according to the instructions in paragraph 4, which may include additional procedures, like preconditioning in other test equipments (e.g. heat treatment).
    按照第4段的說明準備試樣，也許將包括附加步驟，如在其他試驗設備中進行預處理（比如熱處理）。
     
    5.1.1 Test object orientation:  Components or test objects in the chamber shall be placed on/ mounted to non-corrosive surfaces in the appropriate agreed upon position.  If the item is flat the test surface shall be within an 15-20° angle from vertical.  Note that the inclination determines the amount of wetness collected on the panel and hence, the salt load when this film is subjected to climate control, which in turn influences the test result.
    5.1.1  試樣的朝向：試驗箱中的零部件或試樣應按照商定的朝向，放置或固定在防腐蝕的表面上。如果試樣是平的，那么試驗表面應在離垂直線15-20°角度范圍內。請注意，板的傾角決定了溶液的收集量，從而影響試驗片受環境控制時的鹽負荷，進而影響試驗結果。
     
    5.1.2 Test object support:  If it is necessary to suspend the objects, the material used shall be made of non-metallic inert materials.  The test stands must not obstruct passing of air, nor disable proper drainage (The photo in fig. 4 shows an example of open well-drained supports for flat panels)
    5.1.2 試樣的夾具：如需將試樣托起，夾具應采用非金屬的惰性材料，而且不得阻礙空氣流通或排水（圖4就是一個開放且排水暢通的平板試樣夾具）。
     
    5.1.3 Test object exposure to salt spray:  The component or test object shall be placed approximately 1 m from the spray heads if an automated spray rig is used.  Flat samples in angled position must have their full horizontally projected surface exposed to spray collection (see drawing in fig. 4). This will also support a sufficient air circulation around the panels. Other test objects geometries than flat panels must obey these criteria as far as practically feasible.
    5.1.3  試樣曝露到鹽霧中：如使用自動噴灑裝置，零部件或試樣應放置在離噴頭1米左右的位置。按一定角度放置的平試樣必須讓其水平投影面完全曝露到噴灑液體收集區域（見圖4）。這還有助于板周圍的空氣流通。對于平板以外其他幾何形狀的試樣，只要能實際操作，都必須遵循這些標準。
    Fig. 4  Example of open and well drained fixture
    留言